1. 機械泵的轉動部份，少氧化錫的產生和整流層的堵塞，重複性能高，波峰平穩度更高，
2. 直接對焊錫液整體作用力、可形成均一的波峰高度
3. 特殊設計機械泵的部份,維修保養容易、方便，
4. 波峰噴孔／噴嘴調整後擋板裝置，使焊錫品質控制更容易，更理想的數字化，
5. 良好的人機對話功能，良好的流量控制性能，
6.可實現鍚槽的小型化
7.取出噴嘴，清除氧化物，維修保養簡便易行，
8. 波峰平面的穩定性比過去機械式泵更平穩,波峰的左右高度變動幅度+/-0.4mm
|
|
|
|
| 產品規格︰ | Automatic soldering machine specifications
1. The application book specifications of specifications apply to a lead-free automatic
soldering machine model No.LG-350NPB
2. I perform flux application in sprey fluxer, and a summary book device of the devices is
an automatic soldering device to perform in preliminary heating, soldering, a cooling
process in the transportation process of the soldering device.
3. Machine consistion according to the follows.
1) Entrance chain conveyor 1set
2) The main body of machine 1 set
3) Main transportation conveyer 1 set
4) Preheater unit 1set
5) Cast iron solder pot for lead-free 1 set
6) LCD-operation panel 1set
7) A board transportation finger 1 set
8) Finger cleaner 1 set
9) Emergency stop switches 2places
4. The basic specifications of the machine
① Board effective dimensions ： Min.60 X 150mmMax.350 X 400mm
② Board thickness ： 1.6mm correspondence
③ It is lower part effective dimensions in a board
： The top surface, A 100mmH /lower part, Less than 8mm
④ Lead length ： 5mm ～Max.8mm
⑤ Board catching hold of charges ： More than both end faces ３mm
⑥ Transportation angle ： ４ degrees
⑦ Transportation direction ： left ⇒ right
⑧ Transportation height ： 750mm ±20mm（at 4 degrees ）
⑨ Input power supply ： 3φ 380V 60Hz28Kw/hr
⑩ Supply air pressure ： More than 0.5Mpa
⑪ Colore ： Standard color / white
5. Automatic soldering machine model No:LG - 350NPB type
1) Constraction
① The main body frame consists of a channel, a corner pipe, an angle. is covered with a
flat steel sheet, and, in the front, a hatchback-type door, the front lower part and
the rear consist of a desorption panel .
② Air exhaust duct ： φ200×2 places （More than exhaust quantity 25m3 / min）
③ Main body general view dimensions
： 3,280×1,550×1,300mm（Length X depth X height mm）
④ Supply power supply ： 3φ380V about 28Kw
２) Entrance chain conveyor
①Transportation method ：Carrierless type both ends separation belt transportation
② Transportation angle ： Main conveyer is equal (4 degrees)
③ Transportation height ： 750 ±20mm（at 4 degrees ）
④ Transportation speed ： 600-1800mm / min
（Right and left side independent volume adjustment）
⑤ Chain conveyer length ： 400Lmm
⑦ Transportation motor ： Single-phase alternating current 200V15W ×2pcs
3)Main conveyor
① Transportation method ： Carrierless type
② Transportation speed ： 600-1800mm / min
③ Transportation motor ： Single-phase alternating current 200V100W ×1pc
④ Transportation width adjustment
： Handle-style hand-operated width is variable（60-350mm）
⑤ A transportation nail ： Lug system Finger D-40
⑥ A transportation angle ： 4 degrees
4) Preheating unit
① Top side : COVER PREHEATING UNIT ( UPPER SIDE )
(PCB Temp.: 25~100 degree C)
② Botton side : LOWER SIDE PREHEATING UNIT
(PCB Temp.: 25~200 degree C)
③ Control system：2 zones independent temperature adjustment by the SSR-PID control
③ Heater capacity ： 380V 13.2Kw(2.7kw×6pcs=16.2kw)
④ Others ： It is with a tunnel-type cover
5) Cast iron solder pot
① Materials
Pot ： Cast iron + ceramic coating
Chamber / Nozzle ： SUS316 + Special Nitriding processing
② Heater capacity ： 3φ 380V 10.5KW sheathed heater indirect heating type
③ Primary wave inverter motor aspect 200V200W×1pc
Secondary wave inverter motor aspect 200V200W×1pc
④ Swing motor ： Single-phase alternating current 200V25W（Speed control type）
⑤Quantity of solder ： About 400kg (lead-free solder specific gravity： 7.4)
⑥Nozzle
Primary nozzle ： Three lines holes of Gemini swing method flat board type
Secondary nozzle ： Barias type
⑦ Wave height ： Operation nomal use Max. 8mm
⑧ Start up time ： about 2.5Hr (normal temperature - 250 degree C )
weekly timer in operation time.
⑨ Maximum temperature ： About under 280 degree C
⑩ Others
：Solder pot up-down/ drawer mechanism with a hand-operated handle.
6) Fresh air introduction-type cooling fan
① Upper part cooling fan ： Single-phase alternating current 200V21W ×2pcs
② Lower part cooling fan ： Single-phase alternating current 200V21W ×2 pcs
③ Operation switch ： on-off is possible with a panel
7) Emergency stop switches
① Each one in an entrance and t exit
8) Finger cleaning unit
① IPA supply pump ： Diaflum-type electromagnetic pump
② Cleaning method ： Circulation-style shower nozzle and brashing
③ Operation ： ON - OFF movement by the panel switch
④ Piping ： Polyethylene tube
⑤ Cleaning brush ： A product made in nylon
⑥ IPA-can receives it in machine |
| 主要市場︰ | 中國大中華 |
| 參考單价︰ | 人民幣 800000 |
| 付款方式︰ | 銀行信用証 |
| 最小訂量︰ | 壹台 |
| 交貨日期︰ | 60天 |
| 認可標準︰ | 日本標準 (JIS) |
|
|
| 選擇圖片 |
 |
|
|
|
|
